BR Jumping Saddle Puccini I
BR Jumping Saddle Puccini I
The BR jumping saddle Puccini I is made of vegetable tanned leather, finished with soft aniline leather. The saddle has close contact cushions filled with soft, resilient polyurethane foam to ensure that the rider sits close to the horse. In addition, a good balance point for the rider was sought and the saddle was built slightly forward for optimal support during the jump. The medium-deep seat and the generously padded knees are covered with extra soft leather for optimal comfort. The small, sturdy knee and calf rolls ensure a good leg position and optimal support. The base of the Puccini I consists of a flexible polyethylene saddle tree. The saddle is equipped with girth straps made of latigo chrome leather, which ensure a stable saddle position. The sweat leaf is provided with a leather reinforcement on the underside to prevent wear by the stirrup leathers. In addition, the sweat sheet on the edge is partly filled for a nice optical effect. The contrast stitching provides a stylish accent. Including luxurious, padded BR saddle cover with extra storage space for the girth.
The saddle is equipped with:
close contact cushions;
Small, firm knee and calf rolls;
padded knee pads;
Including luxurious, padded BR saddle cover;
The saddle is available in:
The saddle is suitable for:
The saddle is made of:
Vegetable tanned leather, finished with soft aniline leather.
Cushions filled with soft, resilient polyurethane foam;
Kneepads covered with extra soft leather;
Flexible polyethylene saddle tree;
Chrome leather girth straps;
Sweat sheet edge partly filled;
Sweat sheet with leather reinforcement at the bottom.
For extensive sizes, colors and other advice/information about saddles, see specification data and our size chart.
Maintenance of your leather horse saddle
when you have bought a new leather saddle, the leather can be stiff. It is important not to immediately grease a new saddle with leather grease. With a new product, the leather is still untreated and the pores are still open. When you immediately use fat, you block the pores and the leather remains stiff.
It is better for the leather to first deal with leather oil. This is best done by using a brush to oil your saddle well. Make sure that you handle the entire saddle and that the oil retracts well. For the best result, you can let the oil drain overnight. The next morning you can brush the saddle with a dry (tea) cloth. After brushing it is possible to grease the leather. This way you close the pores while the oil is in it. This way the leather of your saddle stays nice and supple for a long time.
With all leather products, you should clean and take care at least once a month with regular use. The proper maintenance of the leather ensures that the product lasts longer. Alternation of leather grease and oil is recommended. If you drive a lot in the open air or use the saddle very intensively, we advise you to do this more often.
1 Release all the closures and disassemble the entire halter or bridle. Use a dry cloth or brush (do not use a brush with very hard hair) to remove any sand or larger pieces of dirt.
Choose a suitable leather soap (or spray) and clean all loose parts well. Do not use too much water because this can make the leather stiff and this is not good for the stitching. After this step let the leather dry well, this goes best at room temperature.
Now that the leather is dry, you can get started with leather balm, grease or a conditioner. Use grease during normal maintenance. When the leather is very dry you can use the best oil. Rub the product well with a soft cloth (use a brush with oil). The end result will be better if you rub it in well.
Then allow it to penetrate well and spread it with a clean dry cloth. Take care that this cloth does not fluff. When you are done with this and the care product is completely absorbed in the leather, you can reassemble the halter or bridle.
- Store leather products in a well-ventilated and dry room. It is not bad when it gets cold, this can not hurt for leather.
- If you treat your bridle one day before use, give the maintenance product sufficient time to withdraw.
- Do not allow bacteria to damage the leather by properly cleaning your bridle / saddle (sweat residue) and the bit (foam residue) after use.
- For a new leather product, first treat with leather oil and then with leather grease, otherwise you lubricate the leather pores and both agents can not properly handle the leather.
- Only use leather care products for real leather. Artificial leather, patent leather and leather with a plastic layer can thus be damaged.
- When a leather product is decorated with stones, you should only take this part with a damp cloth.
In 1988 the excludes brand "BR" (Bieman Riding) was introduced. BR has now grown into a recognized brand that is synonymous with quality within the equestrian world.